Brilliant (diamond cut)
This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article "Brilliant_(diamond_cut)".

A scattering of "brilliant" cut diamonds shows off the many reflecting facets.
A scattering of "brilliant" cut diamonds shows off the many reflecting facets.

A brilliant is a diamond or other gemstone, cut in a particular form with numerous facets so as to have especial brilliancy. The shape resembles that of a cone and is meant to maximize light return through the top of the diamond.

Even with modern techniques, the cutting and polishing of a diamond crystal always results in a dramatic loss of weight; rarely is it less than 50%. The round brilliant cut is preferred when the crystal is an octahedron, as often two stones may be cut from one such crystal. Oddly shaped crystals such as macles are more likely to be cut in a fancy cut—that is, a cut other than the round brilliant—which the particular crystal shape lends itself to.

content

Contents

History

The brilliant cut was introduced in the middle of the 17th century. The first brilliants were known as Mazarins. They had 17 facets on the crown (upper half) and are called double-cut brilliants.

Vincent Peruzzi, a Venetian polisher, increased the number of crown facets from 17 to 33 (triple-cut brilliants), thereby dramatically increasing the fire and brilliance of the cut gem — already much better in the double-cut brilliant than in the rose cut. When seen today, diamonds of that cut seem quite dull compared to modern-cut ones.

Around 1900, the development of diamond saws and good jewellery lathes enabled the development of modern diamond cuts, chief among them the round brilliant cut. In 1919, Marcel Tolkowsky analyzed this cut. His calculations took both brilliance (the amount of white light reflected) and fire (flashes of spectral colors) into consideration, creating a delicate balance between the two. His geometric calculations can be found in his book on Diamond Design.

In the 1970s, Bruce Harding developed another mathematical model for gem design. Since then, several groups have used computer models (e.g., MSU, OctoNus, GIA, and folds.net) and specialized scopes to optimize the round brilliant cut.

Facet proportions and names

Diamond proportions and facets, for the round brilliant cut.

The modern round brilliant consists of 58 facets (or 57 if the culet is excluded), ordinarily today cut in two pyramids placed base to base: 33 on the crown (the top half above the middle or girdle of the stone), truncated comparatively near its base by the table, and 25 on the pavilion (the lower half below the girdle), which has only the apex cut off to form the culet, around which 8 extra facets are sometimes added. In recent decades, most girdles are faceted. Many girdles have 32, 64, 80, or 96 facets; these facets are not counted in the total. While the facet count is standard, the actual proportions (crown height and angle, pavilion depth, etc.) are not universally agreed upon. One may speak of the American cut or the Scandinavian standard (Scan. D.N.), to give but two examples.

These days many people have over used Tolkowsky's "ideal" model. The original model were general guidelines as there were several aspects of diamond cut that was not explored or accounted for in the original model. Excerpts from GIA article What did Marcel Tolkowsky really say?:

Because every facet has the potential to change a light ray's plane of travel, every facet must be considered in any complete calculation of light paths. Just as a two-dimensional slice of a diamond provides incomplete information about the three-dimensional nature of light behavior inside a diamond, this two-dimensional slice also provides incomplete information about light behavior outside the diamond. A diamond's panorama is three-dimensional. Although diamonds are highly symmetrical, light can enter a diamond from many directions and many angles. This factor further highlights the need to reevaluate Tolkowsky's results, and to recalculate the effects of a diamond's proportions on its appearance aspects.

Another important point to consider is that Tolkowsky did not follow the path of a ray that was reflected more than twice in the diamond. However, we now know that a diamond's appearance is composed of many light paths that reflect considerably more than two times within that diamond. Once again, we can see that Tolkowsky's predictions are helpful in explaining optimal diamond performance, but they are incomplete by today's technological standards.

Figures 1 and 2 show the facets of a round brilliant diamond.

Figure 1 assumes that the "thick part of the girdle" is the same thickness at all 16 "thick parts". It does not consider the effects of indexed upper girdle facets.

Figure 2 is adapted from Figure 37 of Marcel Tolkowsky's Diamond Design, which was originally published in 1919. Since 1919, the lower girdle facets have become longer. As a result, the pavilion main facets have become narrower.

Cut grading

The relationship between the crown angle and the pavilion angle has the greatest effect on the look of the diamond. A slightly steep pavilion angle can be complemented by a shallower crown angle, and vice versa. Graphs showing this trade-off are available from folds.net.

Other proportions also affect the look of the diamond:

  • The table ratio is highly significant.
  • The length of the lower girdle facets affects whether Hearts and arrows can be seen in the stone, under certain viewers.
    • Most round brilliant diamonds have roughly the same girdle thickness at all 16 "thick parts".
    • So-called "cheated" girdles have thicker girdles where the main facets touch the girdle than where adjacent upper girdle facets touch the girdle. These stones weigh more (for a given diameter, average girdle thickness, crown angle, pavilion angle, and table ratio), and have worse optical performance (their upper girdle facets appear dark in some lighting conditions).
    • So-called "painted" girdles have thinner girdles where the main facets touch the girdle than where adjacent upper girdle facets touch the girdle. These stones (such as EightStar-brand diamonds) have less light leakage at the edge of the stone (for a given crown angle, pavilion angle, and table ratio). Some diamonds with painted girdles receive lower grades in the GIA's cut grading system, for reasons explained in the GIA article Painting and Digging Out.

Several groups have developed diamond cut grading standards. They all disagree somewhat on which proportions make the best cut. There are certain proportions that are considered best by two or more groups however.

  • The AGA standards may be the strictest. David Atlas (who developed the AGA standards) has suggested that they are overly strict.
  • The HCA changed several times between 2001 and 2004. As of 2004, an HCA score below two represented an excellent cut. The HCA distinguishes between brilliant, Tolkowsky, and fiery cuts.
  • The AGS standards changed in 2005 to better match Tolkowsky's model and Octonus' ray tracing results. The 2005 AGS standards penalize stones with "cheated" girdles. They grade from 0 to 10.
  • The GIA began grading cut on every grading report beginning January 1, 2006 based on their comprehensive study of 20,000 proportions with 70,000 observations of 2,000 diamonds. The single descriptive words are as follows: Excellent, Very Good, Good, Fair, and Poor.

The distance from the viewer's eye to the diamond is important. The 2005 AGS cut standards are based on a distance of 25 centimeters (about 10 inches). The 2004 HCA cut standards are based on a distance of 40 centimeters (about 16 inches).

Polish and symmetry are two important aspects of the cut. The polish grade describes the smoothness of the diamond's facets, and the symmetry grade refers to alignment of the facets. With poor polish, the surface of a facet can be dulled, and may create blurred or dulled sparkle. It may constantly look like it needs to be cleaned. With poor symmetry, light can be misdirected as it enters and exits the diamond.

Hearts and arrows phenomenon

Main article: Hearts and arrows

A diamond that has the top facet or "table facet" exactly perpendicular to the bottom of the diamond or "pavilion" and has its other facets precisely aligned with excellent symmetry, may show patterns that look like arrows from the bottom and hearts from the top. Generally it will need to be viewed loose under a gemscope to see the pattern very well. Although the hearts and arrows property is indicative of a top-tier cut, it does not always mean the diamond will be the most brilliant. Optimal facet placement is the key to brilliance and more important than facet patterning. Not all ideal round cuts will have the hearts and arrows effect either.

See also

References
© jGames.co.uk 2007 (some content from Wikipedia under GDL ) !-- ValueClick Media 468x60 and 728x90 Banner CODE for jgames.co.uk -->
Your Ad Here